Automatic Stand-alone Hardness Units
Automatic instruments for hardness measurement. Available hardness scales are: Shore A, Shore D, Shore A0, Shore 00, IRHD (Micro, Normal, Hard, Low).


Standards the instrument complies with:   
ASTM D1414;   ASTM D1415;   ASTM D2240;   FIAT 50408;   FIAT 50411;   ISO 868;   ISO 48-2;   ISO 48-4;    

Overview 
Stand-alone automatic hardness units are independent hardness measurement devices designed for the execution of hardness tests according to a specific hardness scale.
Stand-Alone automatic units have been designed to meet the requirements of research labs and for production control.

Instruments Characteristics 
Available hardness scales are:
Shore A,
Shore D,
Shore A0,
Shore 00,
IRHD-Micro,
IRHD-Normal,
IRHD-Hard,
IRHD-Low.
The solid construction of the instrument, the high quality sensors and the lifting system with ball-recirculation screw makes them ideal both for research purposes and for heavy-duty production control.
Each Hardness Unit is composed by the following parts: mechanical structure, Testing Unit, Sample Holder with motor-controlled rotation, motor-controlled-Lifting System with ball-recirculation screw, Electronic card
All the parts, which compose the instrument, have been specifically designed for easy interchange in case of failure.


Instrument control 
Stand-alone hardness units can be
controller both with Gibitre Hardness
Software and with Gibitre Electronic
Console.
In case of software control of more
hardness units, each hardness unit
can be connected to a standard pc
using its usb cable and can be used
simultaneously.




Diaphragm centering device for O-rings 
The device permits to perform automatic multiple tests on O-ring or round parts with external diameter up to 75 mm. The device consist of a diaphragm to fix the external diameter of the o-ring and of a gauge-meter for the adjustment of the position of the center of the diaphragm.
The use is very simple:
1) Open the diaphragm and put the o-ring in the center of the device.
2) Close the diaphragm using the open-close leverage until the o-ring is fixed in the center of the device
3) Use the gauge-meter of adjust the position of the device according to the diameter and cross-section of the o-ring
4) Start a multiple test session to make automatically tests in different points of the sample.
To test several o-rings with the same dimensions, you only need to replace the o-ring on the device without any further regulation.


Extension of sample holder 
Extension of sample holder for Automatic Hardness tester with 300 mm diameter. The support, made of Aluminium, can be added to the standard sample holder to increase the bearing surface for the testing of big-size samples.

Accredia Calibration of the instrument 
The instrument is available with ACCREDIA calibration certificate. The certificate is issued by Gibitre ISO 17025 Accredited laboratory.



Standard Calibration service for IRHD Hardness Tester 
The calibration is performed with reference to the requirements of ISO 48 standard.
The service includes:
• Ordinary maintenance of the instrument
• Visual inspection of the Indentor.
• Calibration of the Pre-Load, of the Main Load and of the weight of the Anular foot.
• Calibration of the force application time for Pre-Load and Main-Load (NEW)
• Calibration of the displacement of the indentor in correspondence with several IRHD Hardness readings
• Pre-calibration and Post-Calibration test of the instrument with reference test samples (NEW)
• Issue and e-mail shipment of the Calibration Certificate with traceability to primary standards.


Standard Calibration service for a SHORE Hardness Tester 
The calibration is performed with reference to the requirements of ISO 7619-1 standard.
The service includes:
• Ordinary maintenance of the instrument
• Visual inspection of the Indentor.
• Calibration of the total run of the indentor (readings at 0 and 100 Shore points).
• Calibration of the displacement of the indentor and of the force applied by the indentor in correspondence with several Shore readings (20, 40, 50, 60, 80, 90 Shore).
• Calibration of the force application time (NEW)
• Issue and e-mail shipment of the Calibration Certificate with traceability to primary standards.

Modular Construction 
The main parts of the instrument are: the measuring unit, the sample displacement system and the electronic card.
Those parts have been developed to permit quick and independent replacement in case of failure. This characteristic ensures short recovery time and low maintenance cost.



Industry 4.0 integration 
The instrument and the software have been specifically developed to optimize integration with other environments.
The database in SQL format and the Gibitre_Company_Connect program allows you synchronize your company management software with Gibitre database and to speed up the identification of the tests and to use bar-code readers or similar devices.
The automatic logging service permits to send alarm information to the cloud-service platform of Gibitre Instruments in order to optimize the reaction times of the Service Support.



Available hardness types 
Shore A, Shore D, Shore 00, Shore M,
IRHD (Normal, Hard, Low), Micro-IRHD 
Unit control 
Control via Gibitre Hardness Check Software or via Gibitre Digital Display 
Test modality 
Fully automatic test in different points of the same sample 
Test results calculated for each test 
Shore units: Initial hardness, hardness values after set test times
IRHD/micro IRHD: Hardness at 30 sec (and at set test times), Angle Coeff. of Hardness Vs Time curve, Hysteresis after load removal, Correction of hardness according to sample thickness 
Resolution 
0.01 Hardness point 
Calibration 
Electronic calibration
Report with traceability to primary references
ACCREDIA calibration Certificate (optional) 
Power supply 
110-240 V, 50/60 Hz, 15 W, single phase 
Dimensions 
(W x D x H) 250 x 250 x 600 mm 
Weight 
30 Kg 


Gibitre Instruments
Via dell'industria, 18
Bergamo (Italy)
te. +39 035 461146
www.gibitre.it
info@gibitre.it

Gibitre Instruments
Follow us on
 
Automatic Hardness Check
Automatic instruments for the measurement of Shore or IRHD hardness fitted with motor-controlled sample holder.



Standards the instrument complies with:   ASTM D1414;   ASTM D1415;   ASTM D2240;   FIAT 50408;   FIAT 50411;   ISO 868;   ISO 48-2;   ISO 48-4;    
Overview 
Stand-alone automatic hardness units are independent hardness measurement devices designed for the execution of hardness tests according to a specific hardness scale.
Stand-Alone automatic units have been designed to meet the requirements of research labs and for production control.
Instruments Characteristics 
Available hardness scales are:
Shore A,
Shore D,
Shore A0,
Shore 00,
IRHD-Micro,
IRHD-Normal,
IRHD-Hard,
IRHD-Low.
The solid construction of the instrument, the high quality sensors and the lifting system with ball-recirculation screw makes them ideal both for research purposes and for heavy-duty production control.
Each Hardness Unit is composed by the following parts: mechanical structure, Testing Unit, Sample Holder with motor-controlled rotation, motor-controlled-Lifting System with ball-recirculation screw, Electronic card
All the parts, which compose the instrument, have been specifically designed for easy interchange in case of failure.

Instrument control 
Stand-alone hardness units can be
controller both with Gibitre Hardness
Software and with Gibitre Electronic
Console.
In case of software control of more
hardness units, each hardness unit
can be connected to a standard pc
using its usb cable and can be used
simultaneously.
Diaphragm centering device for O-rings 
The device permits to perform automatic multiple tests on O-ring or round parts with external diameter up to 75 mm. The device consist of a diaphragm to fix the external diameter of the o-ring and of a gauge-meter for the adjustment of the position of the center of the diaphragm.
The use is very simple:
1) Open the diaphragm and put the o-ring in the center of the device.
2) Close the diaphragm using the open-close leverage until the o-ring is fixed in the center of the device
3) Use the gauge-meter of adjust the position of the device according to the diameter and cross-section of the o-ring
4) Start a multiple test session to make automatically tests in different points of the sample.
To test several o-rings with the same dimensions, you only need to replace the o-ring on the device without any further regulation.

Extension of sample holder 
Extension of sample holder for Automatic Hardness tester with 300 mm diameter. The support, made of Aluminium, can be added to the standard sample holder to increase the bearing surface for the testing of big-size samples.

Accredia Calibration of the instrument 
The instrument is available with ACCREDIA calibration certificate. The certificate is issued by Gibitre ISO 17025 Accredited laboratory.

More Info

Standard Calibration service for IRHD Hardness Tester 
The calibration is performed with reference to the requirements of ISO 48 standard.
The service includes:
• Ordinary maintenance of the instrument
• Visual inspection of the Indentor.
• Calibration of the Pre-Load, of the Main Load and of the weight of the Anular foot.
• Calibration of the force application time for Pre-Load and Main-Load (NEW)
• Calibration of the displacement of the indentor in correspondence with several IRHD Hardness readings
• Pre-calibration and Post-Calibration test of the instrument with reference test samples (NEW)
• Issue and e-mail shipment of the Calibration Certificate with traceability to primary standards.

Gibitre calibration service

Standard Calibration service for a SHORE Hardness Tester 
The calibration is performed with reference to the requirements of ISO 7619-1 standard.
The service includes:
• Ordinary maintenance of the instrument
• Visual inspection of the Indentor.
• Calibration of the total run of the indentor (readings at 0 and 100 Shore points).
• Calibration of the displacement of the indentor and of the force applied by the indentor in correspondence with several Shore readings (20, 40, 50, 60, 80, 90 Shore).
• Calibration of the force application time (NEW)
• Issue and e-mail shipment of the Calibration Certificate with traceability to primary standards.

Gibitre calibration service
Modular Construction 
The main parts of the instrument are: the measuring unit, the sample displacement system and the electronic card.
Those parts have been developed to permit quick and independent replacement in case of failure. This characteristic ensures short recovery time and low maintenance cost.
Industry 4.0 integration 
The instrument and the software have been specifically developed to optimize integration with other environments.
The database in SQL format and the Gibitre_Company_Connect program allows you synchronize your company management software with Gibitre database and to speed up the identification of the tests and to use bar-code readers or similar devices.
The automatic logging service permits to send alarm information to the cloud-service platform of Gibitre Instruments in order to optimize the reaction times of the Service Support.

More info

Standards the instrument complies with:  
ASTM D1414; ASTM D1415; ASTM D2240; FIAT 50408; FIAT 50411; ISO 868; ISO 48-2; ISO 48-4;  
Available hardness types 
Shore A, Shore D, Shore 00, Shore M,
IRHD (Normal, Hard, Low), Micro-IRHD 
Unit control 
Control via Gibitre Hardness Check Software or via Gibitre Digital Display 
Test modality 
Fully automatic test in different points of the same sample 
Test results calculated for each test 
Shore units: Initial hardness, hardness values after set test times
IRHD/micro IRHD: Hardness at 30 sec (and at set test times), Angle Coeff. of Hardness Vs Time curve, Hysteresis after load removal, Correction of hardness according to sample thickness 
Resolution 
0.01 Hardness point 
Calibration 
Electronic calibration
Report with traceability to primary references
ACCREDIA calibration Certificate (optional) 
Power supply 
110-240 V, 50/60 Hz, 15 W, single phase 
Dimensions 
(W x D x H) 250 x 250 x 600 mm 
Weight 
30 Kg 
Printable version

Brochure
      
General catalogue
Instrument latest software release
Faq
Related pages
Ask for quotation

a guided way
to ask
for a quotation
Mail

info@gibitre.it
The good old e-mail
ready for every season
Phone

+39 035 460146
Your calls are welcome
monday to friday
03 pm to 01 am
in your local time zone
Local agent


See the whole list

In your country
in your language
at your service
Cookie policy
Questo sito utilizza i cookies (dati permanenti registrati sul tuo PC) per:
- ricordare la lingua scelta
- ricordare i prodotti preferiti
- suggerire prodotti in funzione delle pagine più visitate
- mantenere aperta la sessione (nella sole aree riservata)

Cliccando su "accetta" autorizzate l'uso dei cookies.

Accetto / Accept

This site uses cookies (permanent data on your PC) for:
- remembering the choosed language
- remembering your favorite products
- suggest other products based upon the most viewed pages
- keep the navigation session open (only in the reserved area)

By ckicking on "accept" you authorize the use of cookies.