Mechanical extensometer
for Tensor-Check
Mechanical extensometer for Tensor-Check
Standards the instrument complies with:
ASTM D412; ASTM D638; ISO 37; ISO 5893; ISO 527-1;
ASTM D412; ASTM D638; ISO 37; ISO 5893; ISO 527-1;
The Gibitre Instruments mechanical strain gauge is the dedicated accessory for the Tensor_Check dynamometer, delivering accurate measurement of elongation on rubber and plastic specimens. Engineered for tensile tests on polymeric materials, it captures strain directly on the specimen throughout the test, providing the key parameter for assessing tensile behavior.
Compliance with ISO 37, ISO 527-1, ASTM D412, and ASTM D638 ensures results are traceable and comparable across materials and laboratories, making it the natural choice for Tensor_Check users seeking a measurement solution aligned with recognized methods.
Why choose it:
- Native integration with Tensor_Check
- Accurate elongation measurement on rubber and plastic, consistent with ISO 37, ISO 527-1, ASTM D412, ASTM D638
- Self-stretching clamps with adjustable pressure for continuous, slip-free contact
- Accredited calibration to ISO 9513 and ISO 5893
An essential option for laboratories that rely on precise tools for tensil
Overview
The differential strain gauge is necessary for the execution of elongation tests on Rubber and Plastic specimens. The device allows measuring the elongation of the linear part of the specimen according to the provisions of the standards (see ISO 37, ISO 527, ASTM D 412, ASTM D 638)
Construction characteristics
The extensometer produced by Gibitre has been specifically developed for testing rubber and elastomers taking into consideration:
• the high elongation that can reach rubber and thermoplastic specimens
• the mechanical strength needed to absorb the energy transmitted to the device when the specimen breaks
• the need to easily change the distance between the clamps (reference length) according to the type of specimen
• the need to adjust the closing force of the tweezers at the base to the type of material to be tested.
Operation
The device has two tweezers with an initial distance (reference lenght L0) defined by the standard for the type of specimen in use. The tweezers are attached to the linear portion of the specimen to measure its percentage elongation, with respect to the reference lenght, during the test.
The device complies with the requirements of ISO 5893.
Adjustment of the distance between the tweezers
The distance between the terminals of the strain gauge can be changed in a few seconds by screwing the required spacer into the appropriate hole in the upper strain gauge.
Spacers for 10mm, 20mm, 25mm and 50mm are supplied, together with the device. Different spacers can be supplied on request.
The spacers are calibrated and the actual distance obtained between the terminals is documented in the Calibration Report supplied with the instrument.
In addition, the construction methods of the Gibitre strain gauge allow the customer to simply check the distance between the clamps using standard flat-parallel blocks.
Tweezers for extensometer
The standard supply of the device includes contact points of the tweezers made of stainless steel. The radius at the point of contact with the specimen has been optimized to prevent slipping during the test while avoiding the risk of scoring the specimen at the contact point.
For materials with very low hardness, expanded materials or products with very slippery surface, additional grips with rubberized contact points can be provided.
Rotating extensometer support
To carry out tests that do not require the use of the strain gauge, it is possible to rotate the entire strain gauge holder towards the back of the instrument and lock it in the rest position. In this way, you can use the entire light between the columns of the instrument to carry out tests even on large pieces.
Instrument Characteristics
Resolution
0,01 mm
Total run
900 mm
Adjustment of Reference lenght
Via the rapid replacement of pre-calibrated spacers (10, 20, 25, 50 mm).
Spacers for different Reference lenghts available on request
Spacers for different Reference lenghts available on request
Closure force of the tweezers
Adjustable closure spring
Gibitre Instruments
Via dell'industria, 18
Bergamo (Italy)
te. +39 035 461146
www.gibitre.it
info@gibitre.it
Copyright Gibitre Instruments
