introducing
Abrasion Check
dbg


Abrasion Check
Standards the instrument complies with:
  
Footwear
EN 12770
Rubber & Elastomers
ASTM D5963ISO 4649 
 
Abrasion Check
341
Overview 
The abrasion test gives a comparative evaluation of the resistance to the abrasion of specimens made of vulcanised rubber, plastic and different materials.
The abrasion test according to ISO 4649 and ASTM D5963 is performed on a standard specimen through the use of a certified abrasive paper on a rotating drum with a standard test cycle.
Close
Close

Abrasion Check
526
Description of the test 
• The test allows measuring the volume loss of a cylindrical specimen with 6 mm thickness and 16 mm diameter, which can be obtained by molding or punched from a finished product.
• The specimen is inserted into the locking clamp.
• During the abrasion cycle, the specimen is pressed with a defined force against a rotating drum to which abrasive paper is applied.
• The measurement of the volume variation of the specimen after the abrasion cycle is carried out with a millesimal scale (not included in the supply)
Close
Close
 
Abrasion Check
712
Key Features 
• Easy setup of the instrument to select test mode and perform tests with or without axial sample rotation
• Quick change of the weights to perform tests with 5 N, 10 N or 20 N vertical force
• Detection of premature sample consumption with automatic test stop
• Special design of the sample holder with regulation of closure force of the sample and accurate set of sample protrusion.
• Electronic motor controller for accurate control of the rotating speed of the drum.
• Integrated brush for continuous drum cleaning during the test.
• Drum unlock system to ease the replacement of the abrasive paper and the cleaning of the instrument.
• Protection transparent panel
• EU Labelling
Close
Close
 
Abrasion Check
354
UNIQUE FEATURE: Automatic Detection of Premature sample consumption 
• The instrument automatically detects when the sample is totally abraded and is no more in contact with the abrasion paper.
• The instrument automatically stops and the light warns that the test has not been successfully finished.
• This unique features permits to prevent mistakes in the evaluation of the abrasion resistance of your products
Close
Close
Abrasion Check
326
UNIQUE FEATURE: Drum unlock System 
The drum release device allows the replacement of the abrasive paper to be carried out in a simple and easy way.
The handle in the front position of the instrument allows for quick and easy unlocking.
If you have tried replacing the paper of an instrument that does not have this feature, you will appreciate the difference.
Close
Close
 
Abrasion Check
189
Brush for continuous cleaning of the drum 
The instrument is equipped with a brush for the continuous cleaning of the drum. The device guarantees the removal of the debris left by the specimen, speeding up the execution of the tests
Close
Close
Abrasion Check
230
Rubber Samples from Certified rubber plates for abrasive paper calibration 
Rubber samples obtained from Standard Reference compound for the calibration of the abrasive sheet and for use as a comparative reference compound.
Standard reference compound n°1 in conformity with ISO 4649, annex B, clause B2.
Close
Close
Abrasion Check
159
Mould for compression moulding of test samples 
Mold compliant with ISO 4649 for the preparation of specimens to standards. The mold allows to prepare specimens by compression molding starting from compound.
Close
Close
 
Abrasion Check
167
Rotating cutter for sample preparation 
The die, conforming to the requirements of the ISO 4649 standard, must be applied to a drill press and allows to obtain specimens for abrasion test from finished parts
Close
Close
Abrasion Check
591
Standard Calibration service for an Abrasion Tester 
The calibration is performed with reference to the requirements of ISO 4649 standard.
The service includes:
• Ordinary maintenance of the instrument
• Calibration of the number of revolutions of the drum during the test
• Calibration of the lateral displacement of the sample
• Calibration of the test time
• Calibration of the vertical force on the sample holder (5N and 10 N)
• Calibration of the abrasiveness of the emery paper with Certified rubber samples (3 tests)
• Issue and e-mail shipment of the Calibration Certificate with traceability to primary standards.
Close
Close
 
Abrasion Check
87
Safety Devices 
• Safety protection door with safety switch
• Safety Push-button
• CE labelling
Close
Close
 
Abrasion Check
441
Development and production 
The instrument is totally developed and produced in the plant of Gibitre Instruments in Italy.
All the mechanical parts are produced in the company workshop using modern CNC machines.
Components and sensors from well-known brands are selected in order to ensure the maximum reliability in the measures
Internal trained personnel takes care of all the production stages: assembly, start-up, calibration, packing, shipment and installation.
Close
Close